볼 나사는 공작 기계 및 정밀 기계에서 가장 일반적으로 사용되는 변속기 부품입니다. 주요 기능은 회전 운동을 선형 운동으로 변환하거나 토크를 축방향 반복력으로 변환하는 것입니다. 동시에, 그것은 또한 고정밀, 가역성 및 고효율의 특성을 가지고 있습니다.
편심: 고정측과 지지측 사이의 중심편차를 말합니다.
Inclination: In addition to eccentricity, the installation error caused by the parallel error (up, down, left, and right) or vertical error of the screw nut mounting part between the screw shaft and the guide (LM guide, etc.).
Installation accuracy reference: Refer to the table for the reference value of the installation accuracy of the ball screw. The data in the table is for reference only. Please minimize installation errors. The installation accuracy of the motor support and coupling affects the walking and positioning accuracy of the workbench, so attention should be paid to the ball screw.
Unpacking: Be careful not to hit the nut and end thread. When disassembling the nut, you can manually rotate the nut from one end of the effective thread to the other end. Check whether the resistance is consistent and whether there is obvious bending. Be careful not to disengage the nut screw from the effective thread. Wipe off the surface anti-rust oil and apply lubricating oil.
Maintenance: When the linear speed is less than or equal to 30m/min, grease can be used for lubrication. According to the working conditions, grease should be injected every 300 to 600 working hours. It is recommended that oil lubrication be 30-60m/min, 강제 오일 미스트 윤활은 60으로 간주할 수 있습니다.-100m/분 중공 나사를 주문하고 강제 냉각 및 윤활을 채택하는 것이 좋습니다. 작업 환경을 청결하게 유지하고 먼지 및 기타 불순물이 궤도면이나 너트에 들어가지 않도록 하십시오. 상황이 좋지 않으면 나사에 보호 덮개를 추가하는 것이 좋습니다.
Ball screws are usually used where precise positioning is required. The ball screw has high mechanical efficiency, low transmission torque and almost zero axial clearance, making it an important device in tool positioning and aileron drive applications. However, the resistance and heat generated by continuous operation may cause large friction and positioning errors. Increasing the design coefficient of the ball screw friction will also increase the torque, which in turn affects the positioning accuracy. When the ball is pressed between the ball screw nut and the screw shaft, the wedge effect is a potential source of friction. When rotating in the forward direction, the ball is usually pressed on the nut; on the contrary, the ball is squeezed on the screw shaft. Since the sliding friction coefficient is much larger than the rolling friction coefficient ({{0}}.1-0.3 when there is no movement, 0.001-0.003 when rolling), the wedge effect greatly increases the torque.
Ball screw drive has the following advantages:
①높은 전송 효율. 볼 스크류 전송의 전송 효율은 일반적으로 20.92입니다.-10%, 일반 슬라이딩 나사 전송의 전송 효율은 20.20입니다.-0.40.
②높은 전송 정확도, 안정적인 움직임 및 크롤링 현상 없음. 볼 스크류 드라이브는 기본적으로 마찰 저항이 작은 구름 마찰이며 마찰 저항은 이동 속도와 거의 관련이 없습니다.
③공회전 없이 후진 기어로 작동합니다. 볼 나사와 너트를 미리 조인 후{0}축방향 간격을 제거할 수 있습니다. 이러한 방식으로 반대 방향의 사각 지대가 없으며 축 방향 전달의 정확도와 강성이 향상됩니다.
④뒤집을 수 있습니다. 볼스크류의 마찰 손실이 적기 때문에 회전 운동에서 직선 운동으로 변환할 수 있으며 직선 운동에서 회전 운동으로 변환할 수도 있습니다. 리드 나사와 너트는 모두 드라이브 또는 팔로워로 사용할 수 있습니다.
⑤긴 서비스 수명. 구름 마찰의 마찰 손실이 적기 때문에 수명이 깁니다.
As a precise and labor-saving transmission mechanism, the ball screw is widely used in precision machine tools and CNC machine tools due to the above advantages.
Why not give us a linear challenge?
지금 연락하세요
E-mail: sales@gyballscrew.com Tel(왓츠앱): 더하기 86 17769816967
seller@gyballscrew.com plus 86 17769815516
saleChen@gyballscrew.com plus 86 15325179771
